中国老太婆BB无套内射_泡沫雕刻機日常維護相關步驟_業內資訊_新聞中心_保麗龍雕刻機_五軸_四軸

聯系我們

18560023440

王經理：18560023440
地址：山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

業內資訊

泡沫雕刻機日常維護相關步驟

來源：http://www.bnuj.com.cn 時間：2021-09-10

泡沫雕刻機，本文的內容將再次為大伙兒敘述相關立體式泡沫雕刻機設備維護管理的相關流程，接下去一起訪問文章內容，掌握相關內容！

Foam carving machine, the contents of this article will once again describe the related process of equipment maintenance and management for the three dimensional foam carving machine, and then visit the article content and grasp the related content.

1.定時執行清理電源電路箱的排熱排風系統，請定期維護電氣控制柜上的每個風扇工作是不是一切正常，按時用吸塵機一次電氣控制柜里的塵土，查驗接線端子排螺釘是不是松脫，以確保電源電路一切正常、靠譜應用。

1. Regularly clean the heat and air exhaust system of the power circuit box. Please regularly maintain whether each fan on the electrical control cabinet works normally, remove the dust in the electrical control cabinet with a vacuum cleaner on time, and check whether the screws of the wiring terminal block are loose, so as to ensure that the power circuit is normal and reliable.

2.應盡量避免開電氣控制柜的門，嚴禁開關門工作中，在手工雕刻時空氣中一般都是有塵土、木渣或金屬粉，一旦他們落在電氣控制柜內的線路板或電子元器件上，非常容易造成電子器件間接地電阻降低，乃造成電子器件及線路板毀壞。

2. Try to avoid opening the door of the electrical control cabinet. It is strictly prohibited to open and close the door. In the process of manual engraving, there are generally dust, wood slag or metal powder in the air. Once they fall on the circuit board or electronic components in the electrical control cabinet, it is very easy to reduce the indirect resistance of electronic components and even destroy electronic components and circuit boards.

3.定期維護設備各構件螺絲是不是松脫。

3. Regularly maintain whether the screws of each component of the equipment are loose.

4.機械泵的維護保養：

4. Maintenance of mechanical pump:

A水循環系統打氣泵呼吸口腔內部的金屬絲網制品是用于避免外地人細顆粒物進到泵殼，此過濾網應隨時隨地保持干凈，防止阻塞而造成泵的泵效降低，當離心水泵無需時應當每幾日接電源運行數分鐘，避免泵身長銹沒法一切正常運行。

A the metal mesh products inside the breathing cavity of the air pump of the water circulation system are used to avoid the fine particles from outsiders from entering the pump shell. The filter screen should be kept clean anytime and anywhere to prevent the blockage from reducing the pump efficiency. When the centrifugal pump is not needed, it should be connected to the power supply every few days and run for several minutes to prevent the pump body from rusting and unable to operate normally.

B一般機械泵也應當松掉蝶形螺母，取下紙質過濾芯按時用髙壓汽體濾網，發覺過濾芯換氣不如意或毀壞，應立即拆換，依據使用時間長度能用髙壓加油槍給各處滾動軸承上油。

B for general mechanical pumps, the butterfly nut shall also be loosened, the paper filter element shall be removed, and the filter screen shall be removed with high-pressure steam on time. If the filter element is found to be unsatisfactory or damaged, it shall be removed and replaced immediately, and the high-pressure refueling gun can be used to oil all rolling bearings according to the length of service time.

5.嚴苛依照使用說明書實際操作及遵循應用標準。

5. Strictly follow the actual operation in accordance with the operating instructions and the application standards.

以上內容就是為大伙兒詳細介紹的相關立體式泡沫雕刻機維護保養的流程相關內容，數控雕刻機與人一樣也是有性命的，要想數控雕刻機各構件自始終保持穩定的情況，堅持不懈常常的維修保養是十分關鍵的。那樣能夠把許多常見故障隱患解決在萌芽期情況，避免特發常見故障產生。實際操作工作人員應當培養常常對應用機器設備開展維護保養的良好的習慣！

Unremittingly, the above contents are related to the maintenance process of the three-dimensional foam carving machine for everyone. CNC carving machines are also like human beings. If we want to keep the components of CNC engraving machine from first to last, we must persist in maintaining and maintaining the key. In that way, many common faults and potential safety hazards can be solved in the embryonic stage to avoid special common faults. The actual operation staff should cultivate the good habit of often carrying out maintenance on the application machinery and equipment!