常見的雕刻錯位有左右錯位，上下錯位，X軸錯位,Z軸錯位等，出現這種情況經常讓用戶很是頭疼，今天五軸保麗龍雕刻機廠家小編給大家總結了以下幾個原因，希望對用戶使用雕刻機起到一定作用

The common carving dislocation includes left and right dislocation, up and down dislocation, X-axis dislocation, z-axis dislocation and so on. This kind of situation often gives users a headache. Today, five axis styrofoam engraving machine manufacturer Xiao Bian summarizes the following reasons, hoping to play a certain role in the user's use of engraving machine

1、驅動器的問題：驅動器本身里面的結構或者電子原器件有問題也會(huì )造成錯位現象，這個原因多;溫度過高啊，受磁場干擾啊，潮濕短路啊等，若出現的次數不多，而且把速度降低一點，有時能正常雕刻，這說明驅動器還沒有徹 底壞掉;如果一開始雕刻就錯位就說明驅動器徹 底壞了。解決辦法：修理驅動器或者更換驅動器。

1. Driver problems: problems in the structure or electronic components of the driver itself can also cause dislocation, which is caused by many reasons; If the temperature is too high, affected by magnetic field interference, wet short circuit, etc., and the speed is reduced a little, it can be carved normally sometimes, which means that the driver has not completely broken down; If the engraving is misplaced at the beginning, the drive is completely broken. Solution: repair the drive or replace it.

2、電壓的問題：雕刻機在工作時需要的功率大，如果電壓過低，給驅動器供電不足，功率達不到則會(huì )造成錯位現象，這種情況一般以Y軸錯位為多，出現這種現象有可能是外界電壓不夠，或者在同一線路上有人使用了大功率的設備如電焊等。解決辦法：安裝一個5000瓦的穩壓電源，但這個穩壓電源的誤差范圍不能超過5%，在3%以?xún)??；蛘吆?jiǎn)單的：給這臺雕刻機單獨弄個電源，這個電源上不要再使用其他設備。

2. Voltage problem: engraving machine needs high power when it works. If the voltage is too low, the power supply to the driver is insufficient, and the power can not reach, it will cause dislocation. This situation is generally Y-axis dislocation. This phenomenon may be due to insufficient external voltage, or someone using high-power equipment on the same line, such as welding. Solution: install a 5000 Watt regulated power supply, but the error range of the regulated power supply can not exceed 5%, within 3%. Or simply: get a separate power supply for this engraving machine, and don't use other equipment on this power supply.

3、接口板，主板，轉接板的問題：要是接口板，主板，轉接板壞了，雕刻機在工作的過程中，某一個方向或者是三個軸均不動，造成雕刻錯位。這種錯位對機器的損害比較嚴重，當出現時因立即停機，修好之后再上電運行

3. Interface board, motherboard, adapter board problems: if the interface board, motherboard, adapter board is broken, engraving machine in the process of working, a direction or three axes are not moving, resulting in carving dislocation. This kind of dislocation causes serious damage to the machine. When it occurs, the machine will be shut down immediately, and it will be powered on after repair

4、主軸電機的問題：要是步進電機或者是伺服電機的問題，整個機器在某一方向上都不移動，這種情況出現后表面上跟上面錯位的情況差不多，只是原因不同，一個是控制電路出問題了，沒給電機轉動的信號，電機不轉，一個是電機本身出問題了，即使給它信號，它也不轉，遇到這種情況，都應當立即停機，查出原因，修好之后再通電

4. Spindle motor problems: if the stepper motor or servo motor problems, the whole machine does not move in a certain direction, this kind of situation appears on the surface is similar to the above dislocation, but the reason is different, one is the control circuit problem, did not give the motor rotation signal, the motor does not rotate, one is the motor itself has a problem, even if the signal is given to it, It doesn't work either. In this case, it should be shut down immediately, find out the cause, and power on after repair

5、機床本身的問題：機床上的某個部件有問題或者是松動，表面有雜質等也會(huì )出現錯位現象;如聯軸器松了，壞了，都會(huì )出現錯位;導軌，絲桿上長時間沒有清洗加油也會(huì )出現錯位現象;機床線要是斷了也會(huì )出現錯位現象。

5. Problems of the machine tool itself: a part of the machine tool is defective or loose, and there are impurities on the surface; If the coupling is loose or broken, there will be dislocation; If the guide rail and screw rod are not cleaned and refueled for a long time, there will be dislocation; If the machine line is broken, there will be dislocation.

6、各部分連接控制線接觸不好(功控線傳輸線)。解決辦法：將所有連線拆掉再裝。

6. Each part of the control line connection is not good (power control line transmission line). Solution: remove and install all the wires.